Amplificatore Bluetooth TWS APT-X TWS da 2x50W
  • Amplificatore Bluetooth TWS APT-X TWS da 2x50W
  • 2x50W TWS APT-X TWS Bluetooth Amplifier with Power Supply, C

AMB2050TR KIT2 - 2x50W Bluetooth Amplifier TWS APT-X with Volume Control and Power Supply

New
AMB2050TR KIT2
1 PCS
€ 106.39
Tax included
Quantity
Only few in stock

Description

Bluetooth Class D 2x50W TWS / APT-X Stereo Amplifier - with Power Supply, Cable and Volume Control

LUXUS AUDIO - AMB2050TR KIT2

The AMB2050TR Board is a Class D Amplifier based on the TPA3116D2 chip with integrated bluetooth module and TWS on board system.

The output power of the class D amplifier is 50W with a supply voltage of 24V. The supported voltage range varies from a minimum of 10V to 24V. Passive loudspeaker drivers varying from a nominal impedance of 4 to 8 ohms.

The sources used, in order to send musical signal to the class D amplifier, can be connected via cable (RCA) or by means of Bluetooth 4.0 protocol, selectable via micro-switch on the board.

AMB2050TR can automatically detect the Aux / Line input in the audio input. The Bluetooth audio source has a higher priority. When Bluetooth audio is paused or bluetooth is disconnected. The amplifier will output the Aux in / Line audio. If you want to manually select the Aux in / Line in and Bluetooth audio source, select AMB2050TR. TWS mode supported. Users can transmit audio to 2-pair amplification cards simultaneously without wires.

Multiple AMB2050TR cards can be connected together to become a multi-channel amplification system. The audio output port can also be connected with a subwoofer amplifier card. BVC port: The BVC port can connect with our audio volume controller to control the Bluetooth audio volume.

The salient point is supported by APT-X and TWS. Therefore, users can transmit audio to 2-pair amplifiers at the same time wirelessly. It perfect for your Hi-Fi application. You may want to associate a mobile phone or computer (etc.). Power the amplifier board. Use your phone or PC (etc.) To search for a new Bluetooth device. The module will appear as "AMB2050TR". You dont need a PIN, match it and then you can listen to music.

amplificatore in classe D Bluetooth con TWS

Dettaglio di connessione amplificatore in classe D

AMB2050TR can automatically detect the Aux / Line input in the audio input. The Bluetooth audio source has a higher priority. When Bluetooth audio is paused or bluetooth is disconnected. The amplifier will output the TV sound.

scheda AMB2050TR con TWS

AMB2050TR + AMB2050TR, Both RCA inputs and Bluetooth audio volume can be controlled via the BVC port.

Schede AMB2050TR

Multiple AMB2050TR cards can be connected together to become a multi-channel amplification system. The audio output port can also be connected with a subwoofer amplifier card.

Scheda TWS AMB2050TR

2 cards work in TWS mode

* The user must remove the Aux slave card in Enable jumper before associating 2 cards.

Download below the Procedure to Connect two APT-X Bluetooth Receivers in TWS mode.

   Download Procedure

collegamenti scheda AMB2050TR con TWS

 Technical Specifications Card AMB2050TR

Parameters Test Conditions Value
Supply Voltages (VDC) - 10-24V
Idle Power SD Floating 1.3W/2.5W
Standby power SD linked to GND 0.1W/0.3W
Maximum current 100W @ 4Ohm 5.29A
Efficiency 50W @ 4Ohm 87%-92%
Minimum load impedance - 3.2Ω
Switching frequency SD Floating 394KHZ
Gain - 24dB-26dB
Input Sensitivity (RMS) @ 4Ω, 50W, 1KHz 808mV
Input impedance - 22KΩ
Output power

@ 4Ω THD + N 1%

@ 4Ω THD + N 10%

36W

50W
Bandwidth @ ± 3dB @ 4Ω 20Hz-20KHz
THD

@ 4Ω, 1W, 1KHz

@ 4Ω, 10W, 1KHz

0,0299%

0,073%

Other Features Sheet AMB2050TR

Parameters Specifications
Chip TPA3116D2
Dimensions 6.9 x 10.3 x 2,5 cm
Bluetooth  4.2
Power 2 x 50W
Amplifier class D
Volume control BVC
Short-circuit protection Yes
Overtemperature protection Yes

Technical Features Volume Control VCB0M01

Parameters Name Pin Direction Description
Audio input GND - -
R Analog In Audio In
L Analog In Audio In
Audio output GND - -
R Analog Out Audio output, connect to the amplifier board
L Analog Out Audio output, connect to the amplifier board
Bluetooth control 5V - -
GND - -
INC Digital Out Bluetooth + audio volume
DEC Digital Out Bluetooth + audio volume
SEL Digital In

Bluetooth / single-ended selection

1-Bluetooth,

0-Single-ended select

Power Supply Technical Features ALC24V6AJ

Parameters Value
Producer Epson
Output power (W) 144
Output voltage (V) 24
Output current (A) 6
Input voltage (V) Universal Input 110/230
IP classification No IP
Technology AC/DC
Dimming No Dimming
Format DESKTOP
Application ITE EN/UL/IEC 60950
Certification CE/GS/UL/CB/CCC/TUV
Width (mm) 67
Height (mm) 35
Depth (mm) 167
Weight (gr.) 630

Do you want to Customize the product? Follow our Guides!

The card Bluetooth is programmable, just download the programming software and carefully follow the different guides, as needed, as listed below.

The same Bluetooth amplifier therefore allows programming of:

• Connection name change
• Connection password entry
• Automatic disconnection configuration
• MONO output configuration
• Tone management
• DSP configuration (APT-X only)

     How to change the name to Bluetooth          

          Enable the Bluetooth Password           

      Connection / Disc. Auto Bluetooth APT-X     

             DSP configuration procedure            

           Mono configuration of Bluetooth        

            Manage Bluetooth Audio Tones        

            Download BlueSuite 2.5                    

  Download CSRA64xxx & CSRA63xxx Tools

How can I use it?

Product Details
Brand
Luxus Audio
Chips
TPA3116D2
Output Power [Watt]
50
Channel
2
Power Supply (Volt)
24
16 other products in the same category:
Comments (0)