Reference: AMB2050TYJ
Brand: Luxus Audio
AMB2050TYJ - 2x50W Bluetooth Amplifier Board TWS-APT-X ADAU1701
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Class D 2x20W amplifier - Bluetooth 4.0 |
AMB2020NJ 2x20W audio amplifier card with Bluetooth module. It has a 20W architecture (based on MAX98400A) and each channel has a power of 20W. Both channels are able to output nominal power simultaneously and continuously. This card can be powered by any DC10V-24V power supply. It can be used to drive two passive 8Ω speakers. AMB2020NJ can also be connected with our TSA1000, TSA1010 or TSA1020 external audio volume control card. People can adjust the audio volume by turning the actual knob.
It perfect for your Hi-Fi application. You may want to associate mobile phone or computer (etc.). Power the amplifier board. Use your phone or PC (etc.) To search for a new Bluetooth device. The module will appear as "TSA9840". You dont need to PIN, match it and then you can listen to music.
• AMB2020NJ can automatically detect the Aux / Line input in the audio input. The Bluetooth audio source has a higher priority. When Bluetooth audio is paused or bluetooth is disconnected. The amplifier will output the Aux in / Line audio.
• There is an extra LINE OUT audio output jack. It is also possible to connect to a subwoofer amplifier board.
• BVC port: the BVC port can be connected to our audio volume controller to control the Bluetooth audio volume.
Parameters | Test Conditions | Value |
Supply Voltages | Derived from the PSRR test | 10 - 24V |
Current limit | - | 3.5A-5A |
Bandwidth @ ± 3dB | @ 8Ω | 20Hz-22KHz |
Efficiency | PO = 2X20W, MAX98400A, PVDD = 12V, RL = 8Ω |
90% |
Minimum load impedance | - | 8Ω |
Switching frequency | - | 265KHz-295KHz |
I earn | - | 9-29.8 dB |
Input Sensitivity (RMS) | - | 620mV |
Input impedance | - | 22KΩ |
Output power |
Stereo, RL = 8Ω, THD + N 10% |
22W |
THD + N |
POUT = da 0,1 W a POUT / 2, fIN = da 20Hz a 20kHz, RL = 8Ω POUT / 2, fIN = 1kHz, RL = 8Ω |
0.3% 0.03% |
Parameters | Specifications |
Chip | TSA9840 |
Dimensions | 9.1 x 5 cm. |
Power | 2 x 20W |
Amplifier class | D |
Volume control | Optional |
Short-circuit protection | Yes |
Overtemperature protection | Yes |
Bluetooth | Yes |
The card Bluetooth is programmable, just download the programming software and carefully follow the different guides, as needed, as listed below.
The same Bluetooth amplifier therefore allows programming of:
• Connection name change | ||
• Connection password entry | ||
• Automatic disconnection configuration | ||
• MONO output configuration | ||
• Tone management | ||
• DSP configuration (APT-X only) |
How to change the name to Bluetooth
Connection / Disc. Auto Bluetooth
Mono configuration of Bluetooth
Download CSRXX_ROM_ConfigTool_3.0.64
Reference: AMB2050TYJ
Brand: Luxus Audio
Reference: AMB2050DR KIT1
Brand: Luxus Audio
Reference: BSA-200 KIT 1
Brand: Dayton Audio
Reference: AMB2015NM
Brand: Luxus Audio
Reference: AMB2020AM
Brand: Luxus Audio
Reference: AA-AB32281
Brand: Wondom - Sure Electronics
Reference: AMB2050YM
Brand: Luxus Audio
Reference: VIVALDI MH
Brand: AXIOLAB
Reference: AMB2050WBAJ
Brand: Luxus Audio
Reference: AMB2015NK
Brand: Luxus Audio
Reference: DGAMP3160
Brand: AXIOLAB
Reference: FUSIONAMP FA123
Brand: Hypex
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent