- Out of Stock
Reference: AA-AB41158
Brand: Wondom - Sure Electronics
AA-AB41158 - Bluetooth V4.0 audio receiver card with BRB6P control panel
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Bluetooth Digital Module 5.0 APT-X I2S output |
If you want to build a Bluetooth digital amplifier card, the AudioB I2S Bluetooth audio receiver module is a good choice for your project. This is a bluetooth 5.0 stereo recevier module, the I2S digital output and the musical resampling frequency is 48KHz. Apt-X supported. Based on QCC3008. We have breakout pins for 2x10 step 2mm. You can easily integrate it into your project.
In the Bluetooth module, PINs 7, 8, 9.10 are the I2S outputs:
7 - GND
8 - BCK I2S synchronous data clock, is a 2.304MHzs quare wave signal.
9 - Synchronous SD I2S data output.
10 - LRCK I2S word selection, 48KHz. 1 - Left channel data, 0 - Right channel data.
Setting switch: We set I2S in normal conditions. Set to SPI when the module needs to be programmed.
Pin | Name | Direction | Description |
1 | GND | - | Mass |
2 | LINE IN_L | Analog input | Entrance line, left |
3 | LINE IN_R | Analog input | Entrance line, right |
4 | GND | - | Mass |
5 | AUX DET | Digital input | Aux In / Enable Line |
6 | GND | - | Mass |
7 | GND | - | Mass |
8 | BCK | - | I2S synchronous data clock |
9 | SD | - | I2S data clock output |
10 | LRCK | - | I2S selected word |
11 | VIN | - | Input voltage + 5V (+ 3.7V to + 5.5V) |
12 | MIC_BIAS | Analog output | Microphone bias output |
13 | NC | NC | NC |
14 | NC | NC | NC |
15 | +1.8V | - | Output voltage + 1.8 V |
16 | GND | - | Mass |
17 | FORWARD | Digital input | 1 - Next Music / Increase Volume - Quickly press S2 to go to the previous song. |
18 | REWIND | Digital input | 2 - Last music / Reduce volume - Quickly press S3 to move to the next song, long press to increase the volume. |
19 | PLAY/PAUSE | Digital input | 3 - Play / Pause - Press S1 to play or pause. |
20 | MUTE | Digital output | 4 - Mute control - if there is an audio output, the MUTE pin will be high level, otherwise it will be low level. |
Parameters | Specifications |
Chip | QCC3008 |
Dimensions | 3.5 x 2.4 cm |
Bluetooth | 4.2 |
HFP | V1.6 |
HSP | V1.2 |
A2DP | V1.2 |
AVRCP | V1.4 |
APT-X | (Supported) |
Digital Output | I2S |
Frequency | 48 KHz |
Bits per sample | 16 bit |
1. Quickly press S2 to go to the previous song, long press to reduce the volume;
2. Quickly press S3 to move to the next song, long press to increase the volume;
3. Press S1 to play or pause;
4. if there is an audio output, the MUTE pin will be high level, otherwise it will be low level.
The card Bluetooth is programmable, just download the programming software and carefully follow the different guides, as needed, as listed below.
The same Bluetooth module therefore allows programming of:
• Connection name change | ||
• Connection password entry | ||
• Automatic disconnection configuration | ||
• MONO output configuration | ||
• Tone management | ||
• DSP configuration (APT-X only) |
Reference: AA-AB41158
Brand: Wondom - Sure Electronics
Reference: BTBY50AJ
Brand: Luxus Audio
Reference: BTBA50DO
Brand: Luxus Audio
Reference: BTBX50AJ
Brand: Luxus Audio
Reference: BTBM50AJ
Brand: Luxus Audio
Reference: BTBI50DJ
Brand: Luxus Audio
Reference: BTBI42DJ
Brand: Luxus Audio
Discontinued. Replaced with BTBI50DJ
Reference: BRAX-BEC BT
Brand: Audiotec Fischer
Reference: MATCH MECBT7DSP
Brand: Audiotec Fischer
Reference: BTCX50AJ
Brand: Luxus Audio
Reference: AA-AB41159
Brand: Wondom - Sure Electronics
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent