Amplificatore a 2 canali ad alta risoluzione 1
  • Amplificatore a 2 canali ad alta risoluzione 1
  • 2 Channel high Res amplifier 12v with crossove

HELIX P TWO - 2 Channel high Res amplifier 12v with crossover

New
HELIX P TWO
1 PCS
€ 798.99
Tax included
Quantity
Only few in stock

Description

2 Channel High Resolution Amplifier - 12V with Crossover

Audiotec Fischer - HELIX P TWO

  DataSheet HELIX P TWO

So much power and sensitivity: the new P TWO thanks to its 2 x 490 Watt RMS output power on two Ohms, this compact amplifier is also able to drive the powerful subwoofers. It is designed to drive 2 x 2 Ohm double coil for all woofers like the new HELIX Q subwoofers.

But despite its brute strength, P TWO is by no means a pure subwoofer amplifier. In contrast, the Ultra HD Class D concept combines an extended frequency response greater than 40 kHz with high damping factor, minimal distortion and excellent signal to noise ratio. Therefore, this amplifier is likewise a perfect companion for heavy-duty front speakers in audiophile system concepts.

Special features

Ultra HD Class D amplifier technology

Compared to conventional Class D amplifiers, this concept achieves a frequency response extended to over 40 kHz in combination with reduced distortion thanks to an advanced integrated feedback design. Ultra HD Class D achieves exceptional "Class AB" sound quality combined with the efficiency of a Class D amplifier.

Signal converters with a native 32-bit resolution

HELIX P TWO uses a latest-generation DA signal converter with a native 32-bit resolution instead of the common 24-bit input for the optical input. The result is unprecedented accuracy in signal conversion that particularly optimizes sound quality at lower signal levels.

Smart Highlevel input

The latest generation of OE car radios incorporates sophisticated possibilities for diagnosing connected speakers. If a common amplifier is connected, error messages and the loss of specific characteristics (eg fader function) appear quite often - but not with the P TWO. The new ADEP circuit (Advanced Diagnostics Error Protection) avoids all these problems without loading the OE radio speaker outputs in case of unnecessary high volumes.

Start-Stop Functionality The HELIX P TWO switched power supply ensures operation even if the battery voltage drops to 6 Volts during the crank of the motor.

Technical Features


Parameters Value
RMS output power / max. @ 4 ohms 2 x 280/560 Watt
RMS output power / max. @ 2 ohms 2 x 490/980 Watt
RMS output power / max. @ 1 Ohm -
4 Ohm bridge -
2 Ohm bridge -
Amplifier technology Ultra HD Class D
Inputs 2 x RCA / Cinch
2 x Highlevel speaker input
1 x Optical SPDIF (28 - 96 kHz)
1 x Remote input 1 x Remote control input
Input sensitivity RCA / Cinch 2 - 8 Volts 
Highlevel 5 - 20 Volt
Input impedance RCA / Cinch 10 kOhm
Input impedance level 13 ohm
Outputs 2 x Outgoing speaker
Signal converter for digital input BurrBrown 32-bit DA converter
Frequency response 10 Hz - 40.000 Hz
Increased bass 0 - 9 dB / 40 Hz - 120 Hz
High pass 15 Hz - 4.000 Hz regelbar
Lowpass 15 Hz - 4.000 Hz regelbar
Bandpass 15 Hz - 4.000 Hz regelbar
High / low slope Butterworth 12 dB / ott.
Digital signal-to-noise ratio input 105 dB (A weighted)
Signal-to-noise ratio analog input 105 dB (A weighted)
Distortion (THD) <0,005%
Damping factor > 200
Operating voltage 10,5 - 16 volt (maximum 5 seconds up to 6 volts)
Inactive current 2400 mA
Fuse 3 x 30 A LP-Mini-fuse (APS)

Other characteristics


Parameters Specifications
Dimensions (H x W x D) 50 x 260 x 190 mm / 1,97 x 10,24 x 7,48 "
Additional features Active crossover, adjustable, bass boost, input mode selector, highlevel input with Advanced Diagnostics Error Protection (ADEP), Auto Remote switch, SPDIF Direct In switch, cable remote control for volume adjustment.
Compatible Suitable for all car brands and versions.

Product Details
Brand
HELIX
Channel
2
Analog input
Si
Type
Helix
Output Power [W]
280
SPIDF Input
Si
Impedance Output [Ohm]
13
16 other products in the same category:
Comments (0)